SoCal Jet Boats
Tech Talk => Engine Mechanical / Electrical => Topic started by: jamiemwedmore1234 on October 23, 2013, 08:40:52 PM
-
I've been running a hei with a CID box for about to years it came out of a hot truck was just wandering if there is a difference between a automotive and a marine distributor as far as a timing curve goes I was told some time ago I needed to have something done to it and I also don't use the vacuum advance on it . Its time at 34 degrees advanced any body see a problem with that !!!!!!!
Sent from my iPad using SoCalJetBoats
-
Getting the mechanical advance set is important and it's not too difficult. If you can find someone with an old distributor machine they can get it set up without having to go out and burn up a tank full of fuel making adjustments.
http://static.summitracing.com/global/images/instructions/acc-31041_31042.pdf (http://static.summitracing.com/global/images/instructions/acc-31041_31042.pdf) Accel kit instructions
http://static.summitracing.com/global/images/instructions/mrg-929g(2)1.pdf (http://static.summitracing.com/global/images/instructions/mrg-929g(2)1.pdf) Mr Gasket kit instructions
http://static.summitracing.com/global/images/instructions/mor-72300.pdf (http://static.summitracing.com/global/images/instructions/mor-72300.pdf) Moroso kit instructions
You can also mix the springs to get an advance curve in between the chart ranges.
-
The MSD HEI instructions have the best information I've found so far.
http://static.summitracing.com/global/images/instructions/msd-8365_frm30256.pdf (http://static.summitracing.com/global/images/instructions/msd-8365_frm30256.pdf) MSD instructions
Happy reading ;)
-
If I remember correctly J&M speed center in riverside has a distributor machine that crew chief is talking about. There all pretty knowledgable there and good people but Steve helped me tune my chevelle in the parking lot there a few years back so if ya can talk to him.
Sent from my iPhone using SoCalJetBoats
-
So I've been trying to find markings to tell me what brand hei I have without pulling it out of the motor no where to be found took the cap and roter off nothing not even a part # any suggestions
Sent from my iPad using SoCalJetBoats
-
It's probably an original GM HEI. Most everything in the links I posted will work except the lock out bushings noted in the MSD instructions.
-
It's probably an original GM HEI. Most everything in the links I posted will work except the lock out bushings noted in the MSD instructions.
where can I find the vacuum advance lock and will it still wrk on a gm distributer and if the motor seems to be running good is it worth the trouble what am I loosing /or going to gain
Sent from my iPad using SoCalJetBoats
-
http://www.summitracing.com/parts/pro-67022c (http://www.summitracing.com/parts/pro-67022c)
http://www.summitracing.com/parts/dui-333333 (http://www.summitracing.com/parts/dui-333333)
There is a couple of lock outs/vacuum advance eliminators available through Summit Racing.
-
http://www.summitracing.com/parts/pro-67022c (http://www.summitracing.com/parts/pro-67022c)
http://www.summitracing.com/parts/dui-333333 (http://www.summitracing.com/parts/dui-333333)
There is a couple of lock outs/vacuum advance eliminators available through Summit Racing.
thanks
Sent from my iPad using SoCalJetBoats
-
I removed my vac adv then drilled a small hole and bolted the advance mechanism to lock it out. Took about 20 min to do. Just another idea.
Sent from my SCH-I535 using SoCalJetBoats mobile app