Post by: stuey93 on September 15, 2016, 06:57:36 PM
Post by: stuey93 on September 15, 2016, 06:59:07 PM
Post by: vwagon13 on September 15, 2016, 10:04:34 PM
Hey Guys, my PVC is running off of a port on my carb is that cool or should I be utilizing a port on my intake? Thanks.
Throw that Pollution Control Valve away. You don't need it. Install breathers on your valve covers. Cap the ports on your carburetor. Your done.
Post by: stuey93 on September 15, 2016, 10:19:46 PM
Post by: GT Jets on September 15, 2016, 11:05:05 PM
When I run two breathers it seems to puke oil excessively
Well the PCV isn't doing a lot at wide open.
You should be running good baffles on the covers and the proper breathers.
You don't mention what engine.
GT
Post by: FordLover on September 16, 2016, 05:54:57 AM
Well the PCV isn't doing a lot at wide open.
You should be running good baffles on the covers and the proper breathers.
You don't mention what engine.
GT
Obviously a Chevy or Olds if its puking oil everywhere!! Lol
Post by: 69kona on September 16, 2016, 06:21:19 AM
Obviously a Chevy or Olds if its puking oil everywhere!! Lol
Hey now! Lol
Sent from my iPhone using SoCal Jet Boats
Post by: Your Mom on September 16, 2016, 06:48:32 AM
Post by: stuey93 on September 16, 2016, 08:37:18 AM
I was just wondering if the port on the carb was cool as opposed to running it off the intake. I've run the dual breather setup and it weird but she seems to be happier with the pcv in place. GT do you have a link to some push in breathers you would recommend with good baffles? Thanks
Post by: GT Jets on September 16, 2016, 08:39:57 AM
Thankfully it's a BBF
When I get a moment I will.
If the port you are talking about is on the baseplate of the carburetor, yes, that is the right spot.
GT
Post by: FordLover on September 16, 2016, 08:43:30 AM
Thankfully it's a BBF
Damn it! Had a two in three chance I was right. Lol
I run a dual breather set up on my BBF. Got rid of the pcv valve. Capped off the carbs. Runs good with very little oil coming out of them, only after a hard run. At first I forgot to put the baffles/plates inside the valve covers that go under the breathers. What a mess! Lol. Ever since then.......much better.
Post by: propless on September 16, 2016, 12:10:04 PM
Hey Guys, my PVC is running off of a port on my carb is that cool or should I be utilizing a port on my intake? Thanks
On the carb is the best place. It spreads that oily mess between the cylinders better. Using one intake port dumps all that mess into one cylinder.
Even with a PCV you still need a good baffle in the valve cover. You want it to be able to breath, but you don't want it sucking bunches of oil down the intake.
Post by: steves86ta on September 16, 2016, 03:13:45 PM
Post by: 69kona on September 16, 2016, 04:20:52 PM
whats blowby?When I blow by you in my boat... Lol Hehehe
Sent from my iPhone using SoCal Jet Boats
Post by: steves86ta on September 16, 2016, 04:22:01 PM
When I blow by you in my boat... Lol Hehehe
Sent from my iPhone using SoCal Jet Boats
ya ya.. havent seen that one yet lol
Im sure the new motor will not have a problem at all though :-(
Post by: 69kona on September 16, 2016, 04:25:31 PM
Sent from my iPhone using SoCal Jet Boats
Post by: steves86ta on September 16, 2016, 04:30:25 PM
How knows .... Just playing 😬👊🏻
Sent from my iPhone using SoCal Jet Boats
I know you to well to be putting something mild back in lol.
Post by: stuey93 on September 16, 2016, 04:38:25 PM
