[riverrat4life]

Oh nm...lol I didn't see the next pic..

Sent from my SCH-I535 using SoCal Jet Boats mobile app

[Chad krieger]

Motor mounts came in yesterday still waiting on gaskets from mondello and milodon and timing chain from jegs and new carb main body. I hope by next week.


Sent from my iPhone using SoCalJetBoats mobile app

[GeneralLee]

I'm jealous. Wanted to start yanking my exterior out and start sanding her down this weekend but that was a no due to the rain. Hopefully next weekend. Till then I'll keep collecting parts lol.

[uncleBOBBY]

This is how I left it tonight....

-beerjet-

Started pumping the oil out


SRC 🚤💨

[beerjet]

Started pumping the oil out


SRC 🚤💨

I had one that went in through the dip stick....

-beerjet-

[randog]

Started pumping the oil out


SRC 🚤💨

This is how I change my oil


Sent from my iPhone using SoCalJetBoats

[Flusher]

Started pumping the oil out


SRC

Please share the details on your put setup.  If you had to do it again, would you go the same route?

I am trying the Harbor Freight Oil Extractor:  http://www.harborfreight.com/6-1-4-quarter-gallon-oil-extractor-46149.html but, as with most HF products, I am not entirely stoked with the results.  Killed my POS Kobalt air compressor, now upgraded to a 10HP, 3-phase, 180 gallon Kellog-American...  Just waiting to get my electric rolled over to 3-phase.  If I can’t hold out any longer, I will swap out my Baldor 10HP single phase motor, but it uses twice the amps.

It would be nice to have something that doesn’t require shop air to run.

Thanks,

Joe

[Ecm101]

Nothing



Sent from my iPhone using SoCal Jet Boats

[Flusher]

This is how I change my oil


Sent from my iPhone using SoCalJetBoats

What is that and how does it work?

[uncleBOBBY]

I had one that went in through the dip stick....

-beerjet-

My buddy had one of those back in the day, the only downfall is they never get all the oil out


SRC 🚤💨

[randog]

What is that and how does it work?

It's a 12 volt pump that is wired to a switch and has a barbed fitting where the drain plug goes and a hose to the pump then a hose with a threaded barbed fitting with a cap so you push the caped hose out your drain in the transom in to a bucket and turn the pump on then I run a quart or two more after its empty to get the old out


Sent from my iPhone using SoCalJetBoats

[GoinBrokeBahner]

Well I'm one step closer to getting motor out and putting new Dooley 10qt Pan on... In order to make sure my dipstick would read correctly I set the pan up in the garage at a slight angle, close to how it will be sitting in boat, and filled it with 9qts of water. Luckily it landed right at the "add 1qt" mark. Added the 10th and it reads perfectly👍 what a relief! Also, I got the temp sensor installed along with a Fumoto Drain Valve. After that was done I started priming parts to the water/fuel seperator set up and will paint tomorrow.

I'm starting to go a little crazy because as I wait for chance to pull motor I start another little project one after another...😖  Not the best thing for my slightly OCD personality!!


Sent from my iPhone using SoCalJetBoats mobile app

[jyeager]

I started detailing a bowl for a buddy. Got 3 fins done so far.


Sent from my iPhone using SoCalJetBoats mobile app

[chaosmotox]

Almost got the motor finished!!!


Sent from my iPhone using SoCalJetBoats

[riverrat4life]

dude, that is effin sexy!!

[MorePower]

Well I'm one step closer to getting motor out and putting new Dooley 10qt Pan on... In order to make sure my dipstick would read correctly I set the pan up in the garage at a slight angle, close to how it will be sitting in boat, and filled it with 9qts of water. Luckily it landed right at the "add 1qt" mark. Added the 10th and it reads perfectly👍 what a relief! Also, I got the temp sensor installed along with a Fumoto Drain Valve. After that was done I started priming parts to the water/fuel seperator set up and will paint tomorrow.

I'm starting to go a little crazy because as I wait for chance to pull motor I start another little project one after another...😖  Not the best thing for my slightly OCD personality!! Good luck man!


Sent from my iPhone using SoCalJetBoats mobile app

Lol! You're not the only one! A simple rebuild on my motor went about 3,000 over my initial budget... Oops...."Whatever it takes to get the boat ready by April 11th!"

[76NORDIC]

Started pumping the oil out


SRC

   Hey UB where did you get that pump Does it work good I just let mine drain thru the hose, it definately is a 12 pack wait

[uncleBOBBY]

   Hey UB where did you get that pump Does it work good I just let mine drain thru the hose, it definately is a 12 pack wait

I got it when i worked at chevy back in the day
It was the pump out of the power steering flusher
Its just a 12volt fluid pump


SRC 🚤💨💨💨💨💨

[tpltrbl303]

Gassed it, washed it and in an hour I launch it

Sent from my DROID RAZR HD using SoCal Jet Boats mobile app

[challenger76]

Looked at it and wished I was at the river with a beer in my hand hahaha

Sent from my SAMSUNG-SGH-I747 using SoCalJetBoats mobile app

[GoinBrokeBahner]

Looked at it and wished I was at the river with a beer in my hand hahaha

Sent from my SAMSUNG-SGH-I747 using SoCalJetBoats mobile app

X2!


Sent from my iPhone using SoCalJetBoats mobile app

[chaosmotox]

Pick up the boat today got the bilge gel coated


Sent from my iPhone using SoCalJetBoats

[svssr95]

That looks Purdy.......


Sent from my over priced thinga majig.

[who yo daddy]

I had my pretty assistant helping me!! God bless her!!😍😎haha


Sent from my iPhone using SoCalJetBoats mobile app

[81sprint]

There ya go Art! That's what I'm talkin 'bout

Sent from my SAMSUNG-SGH-I337 using SoCal Jet Boats mobile app